Maxwell Winches
Winches, Capstans and Windlasses for

 

Deck Gear and Solenoids 

AUTOCLEAT - FROM MAXWELL MARINE
The ultimate mooring cleat.

PUSH BUTTON MOORING LINE RELEASE
Imagine being able to release your boat’s mooring lines at the press of a button. No more turning your guests into crew. It provides complete control at the push of a button. The AutoCleat will release any line configuration - loop, figure 8 or slip knot.

CLEAR DECKS AND PASSAGEWAYS
Smart boat design means clever utilisation of every space and surface available. The AutoCleat provides a strong, secure mooring point while berthed and when not required, retracts flush at the push of a button leaving those valuable surfaces uncluttered. No more stubbed toes and no more snagged fishing lines or halyards.

DESIGNED AND BUILT TO LAST
Cast from a high strength, corrosion resistant stainless steel, the horns of the AutoCleat give exceptional high side-load carrying capacity. With the remaining components manufactured from marine grade materials and composites, the AutoCleat comes complete with a 3 year warranty against manufacturing defects.

THE ULTIMATE CLEAT
The AutoCleat is the only mooring cleat that allows you to release your mooring lines, regardless of how the line is secured to the cleat and also retracts flush into the deck. International patent pending.

SIMPLE AND STRONG INSTALLATION
The AutoCleat has been designed with the home handy-man in mind. In less than 20 minutes using some basic tools, the AutoCleat can be installed and fully operational. Only two low amperage wires are required to power up the AutoCleat. The AutoCleat gains strength from being fixed into the deck of the boat.

THE LITTLE EXTRAS
Due to the unique design of the crossing ‘horns’ the AutoCleat secures the mooring line above the deck not on the deck and thus reducing line wear on the boat. The AutoCleat comes standard with a Power Failure Over-ride (PFO) button located in the deck plate. The PFO allows the unit to be operated in the event of boat electrical power failure, always providing a secure mooring location. For more informatiion visit www.strongmarine.com

FEATURES

  • Push-button mooring line release
  • Clear decks and passageways
  • Designed and built to last
  • Easy to install
  • Modern clean styling
AUTOCLEAT SIZING AUTOCLEAT 200 AUTOCLEAT 250 AUTOCLEAT 300
Tip to Tip distance 200mm
(8")
250mm
(10")
300mm
(12")
Under-deck Clearance 170mm
(7.7")
225mm
(8.9")
270mm
(10.6")
Maximum side load 3,000kg
(6,600lb)
7,500kg
(16,500lb)
11,000kg
(24,200lb)
Mooring release load 30kg
(66lb)
75kg
(165lb)
100kg
(220lb)
Product weight 2.5kg
(5.5lb)
5kg
(11lb)
7.5kg
(16.5lb)
Water Ingress rating IP66 IP66 IP66
Optional Drip Trap Available Yes Yes Yes
12 V Yes Yes Yes
24 V Yes Yes Yes
Internal Electrical Protection Yes Yes Yes
Maximum Current Draw (12V) 6amps 25amps 25amps
PFO (Power Failure Override) Yes Yes Yes
Guide to boat sizing to 12m (40') 12m (40')
to 18m (60')
17m (55')
to 30m (100')

 

Autocleat
FOOTSWITCHES

PDF document to read

DUAL DIRECTION SOLENOIDS
Used in conjunction with remote up/down panel, Auto Anchor™ 500C/RC, roving hand held remote control and/or footswitches to switch the motor in the required direction.

  • Heavy-duty solenoids, suitably rated for our winch motors
  • Optional, ignition protected solenoids available
  • Available in 12V or 24V DC for permanent magnet and series wound motors
  • Sealed in a weather proof box
  • Installation in a dry area is always recommended

 

DUAL DIRECTION SOLENOIDS

FOOTSWITCHES
Maxwell heavy-duty, weather resistant units have a UV stabilised water proof diaphragm and are supplied complete with mounting instructions and screws.

  • Rated at 200 amps and suitable for 12V or 24V applications
  • Nickel-plated copper contacts ensure corrosion-free, reliable operation
  • Available in UV stabilised plastic or polished stainless steel covered versions
  • Uncovered versions are also available.
FOOTSWITCHES